There are no products in your shopping cart yet.
Xray
Loading...
XRAY Rear Drive Axle - Hudy Spring Steel - 365340
XRAY Rear Drive Axle - Hudy Spring Steel - 365340
XRAY Alu Eccentric Motor Bulkhead Insert - 364090
XRAY Alu Eccentric Motor Bulkhead Insert - 364090
XRAY ALU 3-PAD SLIPPER CLUTCH PLATE WITH ADAPTER - 7075 T6 HARD - 364121
XRAY ALU 3-PAD SLIPPER CLUTCH PLATE WITH ADAPTER - 7075 T6 HARD - 364121
XRAY COMPOSITE GEAR DIFF BEVEL & SATELLITE GEARS (2+4) - 374930
XRAY COMPOSITE GEAR DIFF BEVEL & SATELLITE GEARS (2+4) - 374930
XRAY STAINLESS STEEL BATTERY WEIGHT 35G - 326181
XRAY STAINLESS STEEL BATTERY WEIGHT 35G - 326181
Xray Delrin Side Linkage Shaft (2), X378150 - 378150
Xray Delrin Side Linkage Shaft (2), X378150
Xray Rear Brace - Graphite 2.0mm, X373080 - 373080
Xray Rear Brace - Graphite 2.0mm, X373080
Xray Link Rear Brace - Graphite 2.5mm, X373081 - 373081
Xray Link Rear Brace - Graphite 2.5mm, X373081
Xray X12'14 Rear Brace - Graphite 2.5mm, X373083 - 373083
Xray X12'14 Rear Brace - Graphite 2.5mm, X373083
Xray X12 Alu Rear One-piece Wheel Hub - M2 Screw - Narrow - 375043
Xray X12 Alu Rear One-piece Wheel Hub - M2 Screw - Narrow
RC Maker Brass Roll Centre Shim Plate Set for Xray X4 - 1.5mm
Changing roll centres on your X4 has never been easier, rather than undoing the whole screw and having shims flying everywhere, simply loosen the screw, slide the shim plate out, and install the new roll centre shim plate, and re-tighten the screws!
With the success of our Carbon Roll Centre Shim Plates, and the ever demanding focus on weight distribution and adding additional weight down low on the Mid Motor platform, we decided to produce brass versions in the most common thicknesses used today.
Available in commonly used 1.5mm, 2.0mm, 2.5mm and 3.0mm thicknesses, it gives you a great range of roll centre options to choose from, whilst being able to move weight around your car to adjust the front/rear weight bias. Whilst these may not be a large amount of weight, due to the placement on the car being very far from the centreline, it can have quite a big impact on the handling of your car.
We suggest running them both front, and rear. However if you feel you need more steering, you could replace the front with carbon and leave the rear brass. If you have too much steering and need more rear traction, then you could leave them in the front only, and use carbon in the rear.
These can also be stacked with the carbon 0.5mm and 1mm Shim Plates if desired.
Each pack comes with a pair of front and rear (different lengths) identified by the one (front) or two (rear) indents.
Features:
- Easy roll centre adjustment
- 4 Different Thicknesses available for different roll centres (1.5, 2.0, 2.5, 3.0)
- 1.5mm Set adds 6g of weight at the lowest point of the car
- Adds weight at ends of the car to adjust weight bias
- Can be used with any brand Chassis plate
- CNC Machined from high quality Brass in Melbourne, Australia
Includes:
- 2x Front 1.5mm Brass Roll Centre Shim Plates
- 2x Rear 1.5mm Brass Roll Centre Shim Plates
RC Maker Brass Roll Centre Shim Plate Set for Xray X4 - 2.0mm
Changing roll centres on your X4 has never been easier, rather than undoing the whole screw and having shims flying everywhere, simply loosen the screw, slide the shim plate out, and install the new roll centre shim plate, and re-tighten the screws!
With the success of our Carbon Roll Centre Shim Plates, and the ever demanding focus on weight distribution and adding additional weight down low on the Mid Motor platform, we decided to produce brass versions in the most common thicknesses used today.
Available in commonly used 1.5mm, 2.0mm, 2.5mm and 3.0mm thicknesses, it gives you a great range of roll centre options to choose from, whilst being able to move weight around your car to adjust the front/rear weight bias. Whilst these may not be a large amount of weight, due to the placement on the car being very far from the centreline, it can have quite a big impact on the handling of your car.
We suggest running them both front, and rear. However if you feel you need more steering, you could replace the front with carbon and leave the rear brass. If you have too much steering and need more rear traction, then you could leave them in the front only, and use carbon in the rear.
These can also be stacked with the carbon 0.5mm and 1mm Shim Plates if desired.
Each pack comes with a pair of front and rear (different lengths) identified by the one (front) or two (rear) indents.
Features:
- Easy roll centre adjustment
- 4 Different Thicknesses available for different roll centres (1.5, 2.0, 2.5, 3.0)
- 1.5mm Set adds 6g of weight at the lowest point of the car
- Adds weight at ends of the car to adjust weight bias
- Can be used with any brand Chassis plate
- CNC Machined from high quality Brass in Melbourne, Australia
Includes:
- 2x Front 2.0mm Brass Roll Centre Shim Plates
- 2x Rear 2.0mm Brass Roll Centre Shim Plates
RC Maker Brass Roll Centre Shim Plate Set for Xray X4 - 2.5mm
RC Maker Brass Roll Centre Shim Plate Set for Xray X4 - 2.5mm
XRAY Composite Servo Saver - X-Stiff - Set - 372503
XRAY Composite Servo Saver - X-Stiff - Set - 372503
XRAY High-Performance Kevlar Drive Belt Front 3 X 513 Mm - 305432
XRAY High-Performance Kevlar Drive Belt Front 3 X 513 Mm - 305432
XRAY T4'18 ALU LAYSHAFT BULKHEAD RIGHT - ORANGE - 303001-O
XRAY T4'18 ALU LAYSHAFT BULKHEAD RIGHT - ORANGE - 303001-O